| Command |
Description |
| %AANNTTCCFF |
Set Module Configuration |
| $AA0Ci |
Perform Analog Input Channel Zero Calibration |
| $AA1Ci |
Perform Analog Input Channel Span Calibration |
| $AA2 |
Read Configuration |
| $AA3 |
Read Channel Enable/Disable Status |
| $AA4 |
Read Analog Input Synchronized Data |
| $AA5 |
Read Reset Status |
| $AA5VV |
Set channel enable/disable status |
| $AA6 |
Read Excitation Voltage Value |
| $AA7CiRrr |
Set Single Channel Range Configuration |
| $AA7(Data) |
Set Excitation Voltage Output Value/td>
|
| $AA8Ci |
Read Single Channel Range Configuration |
| $AAA |
Perform Excitation Voltage Zero Calibration |
| $AAB |
Perform Excitation Voltage Span Calibration |
| $AAEVV |
Trim Excitation Voltage Output |
| $AAF |
Read firmware version |
| $AAI |
read INIT Status |
| $AAM |
Read module name |
| $AAS |
Set Excitation Voltage As Power-On Value |
| $AAS(Data) |
Set Data As Excitation Voltage Output Power-On Value |
| $AAS1 |
Reload Default Calibration Prarameter |
| #** |
Synchronized Sampling |
| #AA |
Read analog inputs of all channels |
| #AAN |
Read analog input of specificed channel |
| @AA6Ci |
Read Lower And Upper Source Limits of Linear Mapping |
| @AA6Ci(SL)(SH) |
Set Lower and Upper Source Limits of Linear Mapping |
| @AA7Ci |
Read Lower And Upper Target Limits of Linear Mapping |
| @AA7Ci(TL)(TH) |
Set Lower and Upper Target Limits of Linear Mapping |
| @AAA |
Read Linear Mapping Enable/Disable Status |
| @AAAV |
Set Linear Mapping Enable/Disable |
| @AACA |
Clear Latched Alarm * |
| @AACECi |
Clear Event Counter |
| @AADA |
Disable Alarm * |
| @AADI |
Read Alarm Status, DO Status and DI Status |
| @AADO(Data) |
Set Digital Output Status |
| @AAEAT |
Enable Latched/Momentary Alarm * |
| @AAHI(Data) |
Set Hight Alarm Limit * |
| @AALO(Data) |
Set Low Alarm Limit * |
| @AARECi |
Read Event Counter |
| @AARH |
Read High Alarm Limit * |
| @AARL |
Read Low Alarm Limit * |
| ~** |
Host Watchdog OK signal |
| ~AA0 |
Read Host Watchdog Status |
| ~AA1 |
Reset Host Watchdog Timeout Status |
| ~AA2 |
Read Host Watchdog Setting |
| ~AA3ETT |
Set host watchdog timeout setting |
| ~AA4 |
Read DO Power-On and Safe Value |
| ~AA5PPSS |
Set DO Power-On and Safe Value |
| ~AAD |
Read Misc Setting, bit 4 is Sampling Rate |
| ~AADVV |
Set Misc Setting |
| ~AAEV |
Enable/Disable Analog Input Calibration |
| ~AAI |
Soft INIT |
| ~AAO(Name) |
Set module name |
| ~AAHB |
Read Half-Bridge Configuration |
| ~AAHBVV |
Set Half-Bridge Configuration |
| ~AAZOCi |
Read Zero Offset of Channel i |
| ~AAZOCi(Data) |
Set Zero Offset of Channel i |
Note: * Alarm function is only for Analog Input Channel 0
|