V1.2.0 Mar-21-2013 by Alan
Firmware 
                  1. Fix the bug:
	    Fix the reset module issue which leads to the module work abnormally.
	2. Firmware version: v1.19 => v1.20. 
Utility:
	1. Utility does not change. 

**********************************************************************************

V1.1.9 Aug-20-2014 by Alan
Firmware 
                  1. Firmware does not change. 
Utility:
	1.  Fix: Mask address setting fail issue.
                  2.  Version: v1.11 => v1.12

**********************************************************************************

V1.1.9 Aug-20-2014 by Alan
Firmware 
                  1. Fix the bug:
                      Fix the reception lost issue on hardware buffer. 
Utility:
	1. Add check IP function in order to prevent input wrong IP address format. 

**********************************************************************************
V1.1.8  Aug-20-2013       by Alan
Firmware:
	  1. Add function of detecting Etherent IC status per 10 seconds.

Update	: tcpip_dm32.lib => 2013/XX/XX

***********************************************************************************

V1.1.7  May-21-2013       by Alan
Firmware:
	  1. Fix the bug:
	   When CAN Bus is bus off, the I-7540D will recovery until bus off recovered.

***********************************************************************************

v1.1.6  March-08-2013    by Alan
Firmware:
	  1. Fix the bug:
	     When CAN bus broken, the I-7540D is continually reset by WDT.


***********************************************************************************
v1.1.5 September-01-2012   by Alan
firmware:
	1. Optimize performance when using XC-100 lib on Tx interrupt mode.
	2. Fix the bug:
	   Modify the timestamp accuracy correction in CAN bus data received. 


**********************************************************************************

v1.1.4  October-29-2009    by Andy
Firmware:
	  1. Fix the bug: 
	     UDP pair connection mode: When bootup with hugh data came 
	     from the CAN side, data will not be sent to another device.


***********************************************************************************

v1.1.3  April-06-2009    by Andy
Firmware:
	  1. Fix the bug when the CAN baud rate is not match othe CAN device,
	     the 7540D will reset by WDT.
	  2. After sending the command "$P0105BBDSP" and "$P0205BBDSP",
 	     the RS-232/485 parameter will take effective without reboot the system.


***********************************************************************************

v1.1.2  Feb-13-2009    by Andy

Firmware:
	  1. Modify the method of calculating CAN BTR0 and BTR1.
	  2. Fix some bugs that effect the performance of receiving
	     CAN messages.
	  3. Fix DHCP bug


Update	: tcpip_dm32.lib => 2009/01/21

***********************************************************************************
v1.1.1  Dec-23-2008    by Andy

Firmware:
	   1. Fix the ACC and ACM setting bugs
	   2. Modify the timer, MINTXTOUT, MAXTXTOUT and RETX_THR_R2, of waiting
	      client to reconnect.

Update	: 7186EL.LIB => 2008/06/20
	  tcpip_dm32.lib => 2008/10/28

***********************************************************************************
v1.1.0	May-09-2008    by Andy

Firmware:
	   1. Provide the transparent communication between the CAN devices 
	      via Ethernet network.
	      (support TCP/UDP protocol)
	   2. Add four commands for CAN bus pair connection
	      (supported by firmware v1.1.0 or later)	
	   3. Disable telnet listen socket (port 23)
	   4. Add Port 9999 for configuration commands, same as port 10000
	   5. Add InstallUserTimerFunction_us() in XC100Init() for RX TimeStamp used

Utility:
	   1. Configuration items for CAN bus pair connection

Update	: 7186EL.LIB => 2008/02/26
	  tcpip_dm32.lib => 2008/01/21

***********************************************************************************
v1.05	October-15-2007    by Andy

Firmware:
	   1. Add four commands for setting/getting Web ID/Passwd
	      (supported by firmware v1.05 or later)
	   2. Add ID/Password on Web configuration page

Utility:
	   1. Add Web ID/Passwd configuration
	      (supported by firmware v1.05 or later)

Update	: 7186EL.LIB => 2007/09/21

***********************************************************************************
v1.04	August-31-2007    by Andy

Firmware:
	   1. Add two commands for setting/getting BTR0 and BTR1
	      (firmware v1.0.4 or later supported)
	   2. Add some checking function when writing values into
	      EEPROM
 	   3. vcom3223 code => vcom3225 code :
	      support DHCP function and MiniOS7 Utility UDP search

Utility:
	   1. Add user defined BTR0 and BTR1 function
	      (firmware v1.0.4 or later supported)

Manual:
	   1. Add comment for BTR0 and BTR1 function
	   2. Modify some pictures of Vxcomm application
	   3. Change the name of I-7540D to i-7540D

Update	: 7186EL.LIB => 2007/06/21
	  tcpip_dm32.lib => 2007/08/22
	  xc100l.lib => 2007/03/30
	  
***********************************************************************************
v1.03	January-08-2007    by Andy

Firmware:
	   1. Modify TimeTicks variable to GetTimeTicks function.
	      => Old method would cause firmware timer error.

Update	: 7186EL.LIB => 2006/07/14
	  tcpip_dm.lib => 2006/09/19

***********************************************************************************
v1.02	July-06-2006    by Andy

Firmware:
	    1. TX/RX Leds displayed mode
	    2. Removing Com1 debug print
	    3. Bug of receiving 2.0A message in 2.0B mode
	       => Cause RX buffer overflow
	    4. Disable UDP function (bSupportUdp=0)
	       => increase the CAN receive performance when no socket connected
	    5. On CAN Data-overflow => ClearRXBuffer
	    6. Web setup page

Update	: 7186EL.LIB => 2006/07/04
	  tcpip_dm.lib => 2006/04/11

***********************************************************************************